Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

$22.99
Park Tool's versatile and durable 8oz Shop Hammer is a perfectly balanced striking instrument built for a wide variety of shop uses. - Forged steel, precision machined striking face - Non marring, replaceable composite tip - Fiberglass shaft with soft touch grip - 8oz (225g) Head - Length: 12" (30.5cm) - Steel striking face: 1" (25mm) diameter - Plastic face: 1-1/4" (32mm) diameter - Replacement tip: Part #293-8
$71.95
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
$20.99
Removes and installs crank caps on Shimano® Hollowtech II® cranks. Includes built in hook to lift the safety plate, speeding crank removal. Steel, investment cast body provides good leverage and includes an option to use with an 8mm hex wrench for removing seized caps.
$34.99
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
$14.99
A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.
$127.95
An alignment gauge is essential for diagnosing and repairing bent or misaligned derailleur hangers, often the source of shifting problems. The DAG-3 features an all-new design, engineered and built to be light, accurate, and versatile. The sliding indicator can measure derailleur hanger alignment against bicycle rims of any size and rotates out of the way to clear seat stays, racks, and other obstacles, allowing 360-degree measurement. The long, precision-extruded aluminum body is built to exacting tolerances and provides ample leverage for making adjustments. - Compatible with 16" to 29"+ wheels (ISO/ETRTO rim sizes from 317 to 630+) - Replaceable M10 threaded tip - Low-profile head fits low clearance thru-axle derailleur hangers and Shimano Direct Mount hangers - Length: 16.5" (420mm) - Weight: 22.75 oz. (645g)
$41.99
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.
$10.95
The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)
$12.95
Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. The TAP-9 is 6mm x 1mm for cantilever brakes and large fender bosses.
$10.99
12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.
$9.99
A sturdy bicycle cleaning brush with a unique angled and contoured shape – perfect for cleaning cassettes and freewheels as well as tires. With a strong ergonomic handle and stiff nylon bristles, the GSC-4 scrubs away the toughest muck and mess.
$8.99
Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.
$16.95
Park's AWS-8 Hex Wrench Set features Bondhus balldriver ends, which facilitate use when the tool is at an angle to the bolt. This is great for working in hard-to-reach areas, such as reaching water-bottle-cage screws. The AWS-8 has 4, 5, and 6mm wrenches, which are the most common bicycle bolt sizes. Plus, its Y shape and vinyl coating provide excellent leverage and comfort.
$36.99
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.
$72.95
"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"
$249.99
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
$8.95 - $15.00
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip.
$9.99
Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.
$8.95
Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.
$15.00
Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.
$70.00
The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable. Includes the following magnetic 1/4" bits: - 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex - T25 Torx-compatible - #2 Philips cross tip - Bit holder includes empty spaces for 2 extra bits
$13.95 - $20.00
World-famous Park Tool quality wrapped up in a combination metric wrench. Features both open and 12-point two-way ratcheting box ends. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful!
$21.99
Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11
$249.99
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
$104.95
The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.
$8.49 - $10.99
Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.
$15.95 - $19.99
Professional quality T-Handle star-shaped wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions
$25.00
Made for the rigors of everyday shop use, this adjustable tap handle fits many common bicycle taps. • Fits most metric taps from M4-M12 • Fits most standard taps from #8-9/16”
$11.99
• Updated to fit better in the hand with a more rounded, smoother shape • The precision sized SW-7.2 fits the three most popular spoke nipple sizes on the market • Nickel plated for years of service • Designed for the home mechanic. FIts the following size spoke nipples: • .127" (3.23mm) • .130" (3.30mm) • .136" (3.45mm)
$23.95
Park Tool's professional-quality Snap Ring pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl dipped grips. The RP-1 has .9mm tips on straight blades for small, internal snap rings. The tips open from 22mm to 0 (tips touching).
Page 1 of 8 Next page