Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

Park Tool Cutting Facer
$145.95 - $253.04
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
Park Tool Left-Hand Bottom Bracket Tap
$249.99
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
Wheels Manufacturing Inc. BBI Shaft Clamp
$229.00
Precision-machined anodized aluminum clamps designed to allow for easy and secure clamping of round suspension components during service. Designed by Barnett Bicycle Institute and manufactured by Wheels Manufacturing. Kit includes 3 pairs of shaft clamps to fit 15 shaft diameters from 8mm to 28.6mm For use with: - Suspension damper shafts - Suspension damper cylinders - Suspension air-spring cylinders - Suspension piston shafts - Thru-axles Clamp 10-006 fits - 8mm - 9mm - 10mm - 12.7 - 15mm - 15.9mm - 16.7mm Clamp 10-007 fits - 17.5mm - 18.7mm - 19.5mm - 21mm - 22.2mm Clamp 10-008 fits - 23.8mm - 25.4mm - 28.6mm
Pedro's Demi Torque Wrench II & Bit Set (3-15Nm)
$219.99
1/4" Ratcheting Reversible Click-Type Micrometer Torque Wrench with Bit Set and Custom Tool Roll Pedro's Demi Torque Wrench II is designed for left-hand or right-hand thread 3-15Nm torque settings required for critical components such as handlebars, stems, and controls. The new design features an integrated bit holder for storage of 8 bits on the wrench for convenience and versatility and the small overall size and low-profile head are perfect for tight spaces and easy handling. The Demi Torque Wrench II is quickly set using a micrometer-style dial and a simple locking mechanism. Accurate to within +/- 4 percent. Backed by Pedro's two-year warranty. - Integrated bit holder for storage of 8 bits on the wrench - Square 1/4" reversible ratcheting drive designed for left-hand or right-hand thread 3-15Nm torque settings - Small overall size and low-profile head perfect for tight spaces and easy handling. - Includes custom tool roll for wrench and bit storage. Included bits and adapters: - Hex: 2.5, 3, 4, 5, 6, (25mm), 4 & 5mm (50mm) - Torx: T10, T15, T20, T25, & T30 (25mm), T25 (50mm) - Crowfoot: 7 & 8mm Flare - WrenchDrive Adapter: 1/4" square to 1/4" hex
Park Tool PCS-9.3 Home Mechanic Repair Stand
$219.95
"The PCS-9.3 is a basic folding bicycle workstand designed and built for the home mechanic – a stable way to hold nearly any bike off the ground for adjustments, cleaning and repair. Features 18"" (460 mm) of height adjustment and 360 degrees of clamp rotation, positioning all parts of the bike within reach for any mechanic whether seated or standing. The stand's all-steel construction with teardrop-shaped tubing ensures maximum rigidity and stability, with a locking support yoke and upgraded internals for extra dependability. The PCS-9.3 is able to hold up to 80 lbs. (36 kg), which allows for compatibility with virtually all two-wheeled pedal-driven bicycles, including fat bikes and most e-bikes.* The PCS-9.3 quickly folds down for storage and transport with a smooth-operating leg support system that pulls both legs up in one simple motion. The PCS-9.3 is the perfect way to upgrade your home shop. NOTE: The maximum weight capacity of the PCS-9.3 assumes the weight is centered below the clamp and between the legs.? - Fully adjustable clamp fits 7/8"" to 3"" (22 mm–76 mm) diameter tubes and seat posts of any shape and material, including aero posts and dropper posts - Narrow clamping jaws (2.7""/70 mm) fit into tight areas or on short seat posts - Durable textured powder coat finish - Maximum weight capacity: 80 lbs. (36 kg) - Height adjustable from 39"" to 57"" (990 mm–1450 mm) - Base when open forms a triangle of 36"" x 36"" x 48"" (920 mm x 920 mm x 1210 mm) - Folds down to 44"" x 14.5"" (1140 mm x 370 mm) - Weight: 16 lbs. (7.2 kg) - #2848A quick-release collar with accessory pods required for use of PTH-1 Paper Towel Holder or 106 Work Tray"
Wheels Manufacturing Inc. Small Sealed Bearing Press
$215.00
Another indispensable tool for the professional bike shop, the Wheels Manufacturing Press-2 works with bearings that have an I.D. of 10mm or smaller (most front hub sealed bearing fall in this range). It features an aluminum base with 9 open bore and over axle adapters, and a quick release skewer. - Installs sealed bearing sizes 6801, 6802, 6803, 6900, 6901, R6, 688, 608, 609 - All parts are laser etched for easy identification
Campagnolo UT-CN400 Chain Tool
$214.00
Campagnolo UT-CN400 Chain Tool. - Used to install 12-speed and 13-speed Campagnolo chains
Wheels Manufacturing Inc. Bottom Bracket Press Pro Install Kit
$211.00
Complete tool kit for installing wheels manufacturing bottom brackets. Kit includes our new bottom bracket socket tool for installing our BB cups, along with new sealed bearing drifts for the following ID bearings: - 22mm - 24mm - 29mm - 30mm Bottom bracket press pro install kit includes: - UNC 48mm 16-notch socket x 1 - 22x37 drift 1/2" x 1 - 6806 OB 1/2" x 2 - 24x37 OB 1/2" x2 - 1/2" frame drift x 1 1/2-13 x 9. 7" - threaded rod unc x 1 44-48. 5mm - double 16-notch 1/2" socket x 1 - threaded handle x 2
No Image
$204.00
- Drift and over axle set for common thru axle hube and frame bearings - For use with 3/8" press rod - See wheelsmfg.com for full list of contents
Park Tool Bearing Cup Press
$199.95
Park's HHP-2 accurately aligns and presses 1-, 1-1/8-, 1-1/4- and 1.5-inch headset cups into your frame's headtube. It features a quick-release design for fast tool installation and removal, extra-long handles for superior leverage and stepped bushings for precise cup alignment. This versatile tool also presses cartridge bearings and cups into one-piece bottom bracket shells and holds fixed-cup wrenches in place when removing or installing adjustable-type bottom brackets.
Park Tool Dial Indicator Gauge Set
$199.95
Park's Dial Indicator Gauge Set mounts to their TS-2 or TS-2.2 Truing Stand (sold separately). The set makes it easy to view and correct a wheel's lateral and radial run-out within a tolerance of .01mm. Compared to going by the gap between the truing stand pointer and rim, having gauges that put a number on the clearance makes wheel truing easier and more accurate.
Wera Kraftform Kompakt Turbo 1 Driver and Bit Set
$199.94
A part time universal gear integrated in the handle of the screwdriver significantly increases the working speed. The turbo function can either be switched on or off by pressing a button. Turning it off is recommended for fine adjustment and final tightening or loosening of a high torque screw. The robust steel design is maintenance-free and ensures a long product life. Thanks to the Rapidaptor bit holder, the Kraftform Turbo can be used with all conventional 1/4" hexagon bits for a wide variety of screw profiles. With the Rapidaptor function the bits can be inserted directly and can be easily removed by pushing the sleeve forward—allowing single-hand operation. - Quadruples the screwdriving speed in a purely mechanical way (without battery) - Activation and deactivation of the turbo function by a simple push of a button - The fixable universal gear allows powerful screwdriving and easy fine adjustments - Robust, maintenance-free gear made of steel (maximum torque 14 Nm) - 1/4" hexagon take-up with Rapidaptor quick-release chuck
Wheels Manufacturing Inc. Over Axle Bearing Press Adapter Kit
$199.00
- Works in conjunction with Wheels Mfg sealed bearing press (BTI #WZ-9991) to install 10mm ID and larger bearings into hubs with shouldered axles, always pressing simultaneously on both the inner and outer race of the bearing and preventing damage during the installation process - Includes adapters for 12 different bearing sizes ranging from 10mm to 20mm: 6900,6000 (10mm ID); 6901,6001 (12mm ID); 6802,6902,6002 (15mm ID); 6803,6903,6003 (17mm ID); 6804,6904 (20mm ID) - Made in the USA
No Image
$197.00
- Drift and over axle set for less common thru axle hube and frame bearings - For use with 3/8" press rod - See wheelsmfg.com for full list of contents
Park Tool Reamer
$120.52 - $188.99
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
Park Tool Adjustable Axle Set - For DT-5
$187.99
Upgrades the DT-5 to the DT-5.2. - Four telescoping axle adaptors - Two stand off studs for Flat Mount alignment - 12mm front fork thru axle sleeve
Wheels Manufacturing Inc. Headset Press Pro Install Kit
$187.00
The Headset Press Pro Install Kit is a robust, and easy to use tool. The kit includes a machined aluminum handle, 1/2" threaded rod, two machined aluminum drifts and the adjustable press stop allowing for easy drift placement. One drift is machined with multiple steps to fit common head tube inner diameters listed in the compatibility tab below. The other drift has two sizes to press in cups with either 1-1/8" or 1-1/2" bearings. - machined aluminum handle and drifts - red anodized drifts and handles - zinc-plated 1/2" diameter threaded rod - long threaded rod works with long head tubes up to 250mm includes - 1 head tube drift includes - 1 headset cup drift - 1 adjustable press stop - 1 threaded handle includes on 1/2"-13x17" unc threaded rod
Park Tool SK-4 Home Mechanic Starter Kit
$184.95
A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench
Wera 8100 Zyklop Metric Speed Ratchet Set w/Switch Lever
$141.29 - $180.71
Incredibly compact set arrangement with many tools in a minimum of space. A completely new ratchet set feeling with unique textile boxes that are very robust and durable. They can be positioned upright for tidy storage on the workshop shelf. Additional surface protection due to textile outer material. Low weight and volume for simpler mobility. - Convenient direction change thanks to switchover lever - Extremely slim ratchet with long lever - Return angle of only 5 degrees - Take-it-easy tool finder: color coding by size
Pedro's Headset and Bearing Press
$179.99
The Headset and Bearing Press is a professional quality tool designed to precisely and accurately install 1", 1-1/8", 1-1/4", and 1.5" headsets as well as most press-fit bottom brackets. Features include removable, 33cm, ergonomic handles, a precision roller thrust bearing for smooth low-effort pressing, a quick release lower press module for fast tool positioning and removal, and an extensive working range from 60mm to 320mm for ultimate versatility. Two sets of adapters are included with the press. Two Stepped Cup Bushings are sized to fit most 1" and 1-1/8" standard headset cups and nest into press plates ensuring precise alignment. Two 22mm ID Shim Adapters ensure precision alignment of any brand-specific cup bushings designed with 22mm inside diameter. A complete set of compatible press fit bottom bracket bushings is available separately. - 60 to 320mm working range with quick release lower press, precision roller thrust bearing, and removable handles - Includes two stepped cup bushings that fit most 1" and 1-1/8" standard headset cups - Includes two 22mm ID shim adaptors to ensure precision alignment of any brand-specific cup bushings designed with 22mm ID
Crank Brothers Speedier Lever
$144.00 - $172.80
Crank Brothers puts their well-known design aesthetic to the humble tire lever with the Speedier Lever. Can we call a single piece of nylon revolutionary? First off, this thing is tough. It removes and installs wire-beaded DH tires, UST tires, and brand-new road tires easily, without breaking. The genius loop protects your knuckles! It installs tires too, without pinching the tube, just flip it and use the other side. And only one lever is needed to remove even the most recalcitrant tires. Oh Speedier Lever, where have you been all my life?
No Image
$160.00
- Bearing extractor set for medium bearings - (1) 6002, (1) 6003, (1) 6804, (1)6805
Bontrager Rhythm 35mm Hub Bearing Tool
$159.99
• Tool to service the bearings of Rhythm Pro/Elite and Line Elite rapid drive hubs • Blind-bearing puller design assists in removing the driveside 6807 bearing • Please visit the techsite for instructions on how to use • Steel
Park Tool Socket and Bit Set
$154.95
The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.
Park Tool BKM-1 Hydraulic Brake Bleed Kit
$153.95
The BKM-1 Hydraulic Brake Bleed Kit will bleed most models of mineral-oil-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid. - Designed and built for home use and for the rigors of daily commercial use - Includes two syringes, hoses with shutoff clips, multi-size bleed blocks, bleed funnel and a unique attachable syringe mount - Housed in a rugged reusable case - Machined 7075 aluminum fittings to service Shimano, Magura, Clarks, Promax, Tektro, TRP and other brands of mineral-oil-based hydraulic brake systems - Replacement parts available - Brake fluid not included
Park Tool Ratcheting Metric Wrench Set
$153.95
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches
Wheels Manufacturing Inc. Bottom Bracket Sealed Bearing Extractor Set
$152.50
- Bearing extractors set for pushing out 22mm, 24mm, and 30mm ID sealed bearings from bottom bracket cups. - Compatible with Wheels Mfg. 1/2" threaded rod press and handles (PRESS-7 and PRESS-7-PRO). BB-EXT Includes (1) 30mm ID sealed bearing extractor (1) 24mm ID sealed bearing extractor (1) 22mm ID sealed bearing extractor (1) 52mm receiver cup (1) 44mm receiver cup sleeve (1) 42mm receiver cup sleeve (1) 39mm receiver cup sleeve (1) bearing pusher shaft
Wera Series 7400 Pistol Grip Torque Screwdriver
$150.34
Wera torque screwdriver. Featuring a Kraftform pistol handle for high torque transfer, the multi-component handle is easy on the hands and makes for ergonomic screwdriving with hard and soft zones for high working speeds. - Fixed torque setting with highest precision. - Unlimited torque to loosen seized screws - Suitable for bits with 1/4" hexagon head drive - Kraftform torque screwdriver with pistol handle and Rapidaptor quick-release chuck - Rapidaptor technology for rapid bit change - Distinct signal when pre-set value is reached
Feedback Sports Pro Truing Stand
$150.00
Have you ever wondered why all Feedback Sports wash and repair stands have exposed frame above the clamp head? Our Pro Truing Stand is designed to sit atop all of our portable stands! The truing stand also includes a free-standing steel base and a bench-mount adapter for when you’re not traveling to races and top-secret trailheads. This single-arm, precision wheel and rotor truing stand is awesome at home and excels at races, events, or adventure-riding weekends. And with included adapters, it can accommodate the most common wheel sizes for quick-release or thru-axle hub designs.
Pedro's Starter Bench Tool Kit
$149.99
Essential Tool Kit for the Home Mechanic The Starter Bench Tool Kit is designed for the aspiring mechanic looking to get started with the right professional-quality tools and room to grow as new skills are learned. - 11 professional-quality tools packed in a traditional toolbox. - Tool selection focused on essential repair, adjustment, and replacement tasks. - Perfect for the car, traveling to an event, or a home shop setup. Tool List: - Folding Hex/Screwdriver Set: 2.5, 3, 4, 5, 6, +, - - 8mm Hex Tip - T25 & T30 L Torx Wrenches - Tire Lever Pair—Yellow - Quick Link Pliers - Six-Pack Chain Tool - Pro Travel Pedal Wrench - Pro Chain Whip - Cassette Lockring Socket - Cable Cutter